It is currently Sat Jul 04, 2020 1:49 pm



Post new topic Reply to topic  [ 48 posts ]  Go to page Previous  1, 2, 3
Author Message
 Post subject: Re: How many connections should be on the back of the keyed
PostPosted: Sun Sep 01, 2019 1:34 pm 
Offline
Aftermarket Dealer

Joined: Thu Jun 03, 2010 2:49 am
Posts: 333
Location: Edmonton, Alberta
Jlattan75 wrote:
Let me repost my reference. Also you need to know that the plug you see on the right of my cdi has a three point harness plugging into a two point plug on the cdi. On your schematic it's not really clear what points on the cdi the connections go to. I'm also not sure how to post the list you mean in this conversation a link?


This is the wrong CDI, you have a DC CDI. Use the reference in the Hammerhead 250 GTS manual and you will be on the right track.

_________________
Image https://gokart.maximum.parts
Image YouTube
Image Facebook


Top
 Profile  
 
 Post subject: Re: How many connections should be on the back of the keyed
PostPosted: Sun Sep 01, 2019 7:57 pm 
Offline
Initiated

Joined: Sun Aug 11, 2019 2:58 pm
Posts: 36
What about what I found with the wire tracing. And questions galore. Are you thinking? Don't know? Want me to figure it out?

I said also the wiring diagram on pg21 I think doesn't really show pin assignments. I was only using the one I sent for the numbering of the pins not the key. The green ground isn't clear at all. Am I looking at what you want me to see?


Top
 Profile  
 
 Post subject: Re: How many connections should be on the back of the keyed
PostPosted: Wed Sep 04, 2019 8:55 pm 
Offline
Initiated

Joined: Sun Aug 11, 2019 2:58 pm
Posts: 36
What is this blue wire connected to?


Attachments:
20190831_165549.jpg
20190831_165549.jpg [ 3.26 MiB | Viewed 228 times ]
Top
 Profile  
 
 Post subject: Re: How many connections should be on the back of the keyed
PostPosted: Wed Sep 04, 2019 9:01 pm 
Offline
Buggy Addict
User avatar

Joined: Mon Sep 12, 2005 8:08 pm
Posts: 6928
Location: Quad Cities, IL
Just grounded, right?

_________________
Ron

2009 Hammerhead 250SS (it's got a few mods)
Joylaris 400

Gone, but not forgotten: 2005 Carter Talon, 2007 Hammerhead 250SS
Proud member of Team FIB


Top
 Profile  
 
 Post subject: Re: How many connections should be on the back of the keyed
PostPosted: Wed Sep 04, 2019 9:35 pm 
Offline
Initiated

Joined: Sun Aug 11, 2019 2:58 pm
Posts: 36
I can test that. It's connected to passenger side of motor right behind the seat. Just thought it was odd they grounded it there versus the nest of grounds on the other side by the battery!?!


Top
 Profile  
 
 Post subject: Re: How many connections should be on the back of the keyed
PostPosted: Wed Sep 04, 2019 9:48 pm 
Offline
Initiated

Joined: Sun Aug 11, 2019 2:58 pm
Posts: 36
To me it seems my green wire on the cdi is on the wrong pin. Calling it pin 4 in the picture. By the plan it looks like it should be one pin to the left (meaning bottom left of the four pin). I think it's currently on the null spot!?! On the plan what component is the top right on the cdi (marked as blue / yellow) connected to? I see generator then something not marked (might be part of the generator?). Also, not to sound stupid but
is the generator same as stator? How can I test if the green is on the right pin? If I want to change that nest of grounds to something the all connect to safely would you use a bolt on the frame and give them all crimp on I hooks?


Attachments:
20190831_160003.jpg
20190831_160003.jpg [ 3.27 MiB | Viewed 221 times ]
Top
 Profile  
 
 Post subject: Re: How many connections should be on the back of the keyed
PostPosted: Fri Sep 06, 2019 4:16 pm 
Offline
Initiated

Joined: Sun Aug 11, 2019 2:58 pm
Posts: 36
Can I read something across the cdi of n ohm or voltage to verify or oppose my issues?


Top
 Profile  
 
 Post subject: Re: How many connections should be on the back of the keyed
PostPosted: Fri Sep 13, 2019 12:26 pm 
Offline
Buggy Addict
User avatar

Joined: Mon Sep 12, 2005 8:08 pm
Posts: 6928
Location: Quad Cities, IL
I wish I could help, but wiring ain't really my thing. I will tell you that the motor and the frame will be grounded, so if that is a ground wire, it is very common to go to one of the smaller bolts on the case.

_________________
Ron

2009 Hammerhead 250SS (it's got a few mods)
Joylaris 400

Gone, but not forgotten: 2005 Carter Talon, 2007 Hammerhead 250SS
Proud member of Team FIB


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 48 posts ]  Go to page Previous  1, 2, 3


Who is online

Users browsing this forum: No registered users and 0 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group

blackLevel designed by GrafsS



phpBB SEO
© Buggynews.com - All Rights Reserved