Lets all post our wheel sizes and bolt pattern here. To get the bolt pattern you measure the center of the bolts diagonally. (inch X 25.4 = mm) or use this conversion calculator http://mg-jewelry.com/mmtoinches.html

To get the offset for the rim you measure from the center of the rim to the outer edge, you have to do this on both sides and the first number is alwasy the inside.

Here is a link to ATV wheel size and bolt pattern and offset. It is very helpful. http://www.itptires.com/techinfo.html

Example: my Sahara has a 4/110 bolt pattern and a 3+2 offset on the front wheel.

Sahara front--10X5 rim 3+2 - 4/110----rear--10X9 rim 5+4 - 4/137

Blade(all) front 10X5 rim 3+2 - 4/110----rear--10X9 rim 5+4 - 4/137

Kasea AB150 front--8X5 rim - 3+2 - 4/110----rear--10X9 rim 5+4 - 4/137

Twister 250 front--8X5 rim - 3+2--4/110----rear--10X9 rim - 5+4 - 4/137

Twister front--8X5 rim 3+2 - 4/110----rear--10X9 5+4 - 4/137

Trakker front--10x5 rim 3+2 - 4/137----rear--10x9 5+4 - 4/137

Talon GX front--8x5 rim 3+2 - 4/110----rear--9.5X8 4+4 - 4/110

Moded 2004 Talon DLX150IIR front--10x5 rim 2+3 - 4/110----rear--10X8 3+5 - 4/137

This was one of my last posts before being "deleted" yesterday.
Luckally, I wrote the info down!!
Here's what I have according to the math...... (Couldn't figure out the "Offset" thingy, I only went to community college )

My 05' Twister 250..........

(Fronts)
20X7X8
4/108
Center of tire to outside edge of rim = 4 5/8"
9" outside to outside of rim
2.5" deep w/ 3/4" lip
Tire stands 18" from ground to top of tire

(Rear)
22X22X10
4/133
Center of tire to outside edge of rim = 6'
11.25" outside to outside rim
3.5" deep w/ 1" lip
Tire stands 20.5" from ground to top of tire

I also took some other measurements while I was rolling around the garage.......

Widest point on Buggy = 53.5" (Tires)
Ground to floorpan = 11" (Holds this Mes. all across bottom)
Highest point on buggy = 58" (Top roll bar)
Total Length = 90" (F. Bumper to Tailer ball )

So that means your front is a 4/110 and the rear is a 4/137. I will add to above.

Thank you!

2004 Carter Brothers Talon DLX150IIR.

FRONT:
RIM'S - TR ACC STL WHL 10X5 2+3 4/110 part #370845.
TIRES - TR ACC HOLESHOT XCR 21X7X10 part #370988.

REAR:
RIM'S - TR TIR STL WHL 10X8 3+5 4/137 part #370844.
TIRES - TR ACC HOLESHOT XCT 22x11x10 part #370975.

Thank you TalonMan!

I'll take you're word for that jabo
How do you do it!

(So that means your front is a 4/110 and the rear is a 4/137. I will add to above.)

Well Kidinme, you probably measured right, but there isn't a rim with a 108mm, that is why I said it was a 110. Same with the 133mm being a 137mm.

Trakker added...lets keep this going so we can get all the buggies.

What buggies are missing? It would be great to have them all there...

Everyone try to list yours. Even if it is close, I can figure it out from there.