I am going to be there friday morning and will set up in the parking area. check for the chipmunk palce isnt until 3:00.
the folks that want to get there friday can look for my tent in the parking area just down from the lodge. For those that want to run on the flat track 10:00 would be good. go over everthing, then ride the trails, race from 1:30 (after lunch ) till 3:30. repair what needs it, change what needs to be changed.
ride the trails. I am trying to get a suppervised night ride for sat. night _________________ Blade buggies,Carter buggy's, ams (manco) , joyner, parts for almost anything
MRP dealer
Tucker Rocky Dealer
Vega Helmet dealer
I.T.P. tire and wheel dealer
www.mcdonoughpowersports.com
Eric,
Carter and i will be pulling out of Fay. around 6am. Looks to be a 4 1/2 hour trip. I hope to be there around 1:00 ish. The did not give me a check in time when I made reservations, if it's 3 then I will look for you when I get there.
I'm tring to pack lighter than I did for the NE meet in 06'. Will anyone have an air comperssor? I will still pack my small welder but since I'm bringing a motorcycle also I want to leave the generator and compressor at home. Just have to have one to do CVT repairs.
See you guys there.
Ray _________________ Carter Talon GX150IIR, KOSO Clutch, 9 gr rollers, KOSO variator, 1500 RPM spring, CVT snorkel, K&N filtered crankcase+trans vents, Red neck intake w/ uni filter, modified DLX muffler, 132 jet, drilled and shimmed slide, hot coil, hp CDI unit, skid plate.
I'm tring to pack lighter than I did for the NE meet in 06'. Will anyone have an air comperssor? I will still pack my small welder but since I'm bringing a motorcycle also I want to leave the generator and compressor at home. Just have to have one to do CVT repairs.
See you guys there.
Ray
I'll have air and a welder both, Ray. Your welcome to them. What type of bike are you bringing? I'm thinking about bringing one of mine too. _________________ 3206 yerf. too many mods to list. easier to list what has not been modified- seats and steering wheel. plus one set of kidinme's hand made special collectors edition fuzzy dice. We support pole dancing.
well I'm still hoping for a miricle and I can be there. My sons buggy has a bent strut. I have been working 12hours 7 days for the last few weeks so I havent had time to sleep let alone to order parts and repair buggies. If I make it to the meet it will be 3 peeps and two buggies. _________________ 06/07 GSX 150 Carter Talon
07 GSR 150 Carter Talon
A friend of mine is letting me use his Yamaha TT-R 250. It has been in storage for 2 years. I have the carb apart now tring to get the green sludge, that used to be gas, out of it. If all goes well I will be bring it and the Talon buggy. Carter is counting down the days to the trip. I told him he could drive the buggy by himself if I brought the bike to follow him around on. Since you will be bringing your welder and compressor I will leave mine at home. Since we will have power hook ups I can leave the generator home too. Did you ever replace the one in your trailer that went south at the 06' NE meet?
OZ,
Order the strut and pack it. There will be plenty of people there to help install it. Look me up and we can knock it out in about 20 mins. Buggy riders stick together and can repair almost anything at a meet. The 2006 NE meet we did a strut repair on KIDINME's twister, a steering wheel weld job on IM4SEVEN's Keasa, a new intake on DJ's Sun L and a clutch bell resurface on my Talon. Some other repairs were needed at the end of the weekend but too late and trailered home (CKAU's bent rim and my blown tire side wall). Basicly there is enough knowledge (and tools) at one of these meets that we can fix almost anything. Bring it fixed or not we will help.
Ray _________________ Carter Talon GX150IIR, KOSO Clutch, 9 gr rollers, KOSO variator, 1500 RPM spring, CVT snorkel, K&N filtered crankcase+trans vents, Red neck intake w/ uni filter, modified DLX muffler, 132 jet, drilled and shimmed slide, hot coil, hp CDI unit, skid plate.
A friend of mine is letting me use his Yamaha TT-R 250. It has been in storage for 2 years. I have the carb apart now tring to get the green sludge, that used to be gas, out of it. If all goes well I will be bring it and the Talon buggy. Carter is counting down the days to the trip. I told him he could drive the buggy by himself if I brought the bike to follow him around on. Since you will be bringing your welder and compressor I will leave mine at home. Since we will have power hook ups I can leave the generator home too. Did you ever replace the one in your trailer that went south at the 06' NE meet?
I'll plan on bringing a honda CRF150F. If your yami doesn't work out, you use the honda to chase Carter with. Yes and no on that stupid generator. got it fixed , then it went south again, ...needs a carb _________________ 3206 yerf. too many mods to list. easier to list what has not been modified- seats and steering wheel. plus one set of kidinme's hand made special collectors edition fuzzy dice. We support pole dancing.
Yes and no on that stupid generator. got it fixed , then it went south again, ...needs a carb
Must be a techumseh! lol... if it is, it is the high speed throttle linkage... My generator is starting to do that revving and sputtering... it is annoying...
Have fun at the meet!!! What a great attitude Fireman!!!!
you won't need a gene anyway, they have power... just plug in.
I am not sure though, you will likely need an adapter from a 30 amp plug to a 110 if you want to plug in directly. I knoe last year Bill (gogokarting) plugged the welder into the camper outlet and fried the outlet..
I am goin to an rv shop, I will C if they have one...
If anybody needs parts that they know of let Me or BIGE know so we can be sure to bring them..
And what is the count now???
Stu
Stu _________________ PERFORMANCE, OEM PARTS AND ACCESSORIES FOR BUGGIES, ATV'S AND SCOOTERS!!!
Articles
