So I bought a used Dune 150, and I am going to do a full rebuild on it. I have torn it down to the frame, sand blasted and now finished paint. It is ready for the rebuild. I have most of the parts, so it should go quick...I hope!!! I will be adding all the following mods and will inc. pics and helpful hints on here as I go along. If you see anything I can improve on or better ideas, please feel free to voice your opionion.
Modifications:
Engine:
9 gram rollers
1500 main spring
Stock clutch with yellow springs
Uni Filter w/pre charger
130 Main jet
Performance exhaust
Oil cooler
CVT Uni Filter w/pre charger
HP CDI and coil
Dual 12A batteries
Suspension:
Rack and pinion box
Tie rods
Tie rod ends
Reenforced A-arms
14mm Ball joints
Brake pads (all around)
New Front shocks (still TBD)
Blaster Rear shocks
Maxxis 20-7-8 Fronts (looking for 21-7-10)
Maxxis 22-11-10 Rears
Body and Accesories:
New gas/brake pedals and cables
Dash w/Trail tech computer
GT removable sterring wheel
Summit performance seats and covers
4 point harnesses
Gas tank and risers
2 off road lights, with switch and LED bulbs
LED tail/brake light
Roof rack w/ light bar
Rear cargo net and atv cargo bag
Canvas hood, roof and side panels (snap on and off)
Rear oddessey fenders
that looks great. are you foing to use the stock fron a-arms? _________________ Blade buggies,Carter buggy's, ams (manco) , joyner, parts for almost anything
MRP dealer
Tucker Rocky Dealer
Vega Helmet dealer
I.T.P. tire and wheel dealer
www.mcdonoughpowersports.com
Yes, but I reinforced them and added 14mm ball joints. Why do you ask? _________________ Baja Dune 150
9 gram rollers, Yellow main spring, Uni Filter w/pre charger, HP CDI, HP Coil and Plug wire, Gutted exhaust, 130 main jet, all new balljoints and rod ends.
Looks like you're off to a good start there Monk _________________ DRIVE IT LIKE YOU STOLE IT!!!!!!!!!
DAZON 150 SINGLE SEAT
2.5inch rear wheel spacers
1.5inch front wheel spacers
UNI, 130jet, BIGE built intake tube, custom built exhaust, HO coil, adjustable CDI, iridium plug
just wondering. thought you might have some wild suspention ideas _________________ Blade buggies,Carter buggy's, ams (manco) , joyner, parts for almost anything
MRP dealer
Tucker Rocky Dealer
Vega Helmet dealer
I.T.P. tire and wheel dealer
www.mcdonoughpowersports.com
No crazy ideas for the front YET!!! This is my first kart and I have only rode maybe 4 times. I think I need to stick to the basics until I get some on trail experience and knowledge. I do how ever have ideas and parts waiting an IRS set up.
Any crazy ideas up your sleeves? _________________ Baja Dune 150
9 gram rollers, Yellow main spring, Uni Filter w/pre charger, HP CDI, HP Coil and Plug wire, Gutted exhaust, 130 main jet, all new balljoints and rod ends.
Thanks man. I learned from the BEST (buggy news crew!!) _________________ Baja Dune 150
9 gram rollers, Yellow main spring, Uni Filter w/pre charger, HP CDI, HP Coil and Plug wire, Gutted exhaust, 130 main jet, all new balljoints and rod ends.
Ok this is taking a bit longer than I thought. Every time I go to install one new piece, I realize I have a different one I need to put on first.
So as of today I have reran all new wires from box to ignition and lights. Installed Ignition, kill switch and light switch. Front end is put together, but I need the new rack and pinion and front shocks before I can mount to the kart. Both have been ordered and should be here soon. Pedals, shifters and cables all replaced.
Hopefully I can get more done this weekend, once I get the needed parts. I will update with photos after this weekend. _________________ Baja Dune 150
9 gram rollers, Yellow main spring, Uni Filter w/pre charger, HP CDI, HP Coil and Plug wire, Gutted exhaust, 130 main jet, all new balljoints and rod ends.
what shocks are you going with? what happened to your old rack? As per the combo you have, I would skip the filter on the cvt... it gets waaay too hot in there to add a filter to it, other than a piece of t-shirt or something with a band strap or even a zip tie to hold it on... I run without a filter and so far, great results!!! I flush it after every run with water...
When using an oil cooler, be sure to run it for only a few hours, and change the oil a couple times before going on any big rides or anything... this ensures no leaks and a properly operation system... Plus it will flush the new cooler of any potential threats from the factory...
Well..thanks to Mark, Im going to use the 16" shocks with the brackets from his Dune. I was having no luck finding a set of those ZR's in 18's anywhere, and I want to ride. So Im going to use these for now, and keep looking for ZR's.
Nothing really, cracked booties...but I just replaced everything else up front, so i didn't really want to have all that new stuff relieing on the stiff old rack.
Im not sure I could get away with out having something filtering...I live in the desert and its pretty dusty! Shouldn't I be concerned about all that dust on the belt?
The oil cooler has already gone out the window. I had several members tell me no, so I ditched that idea.
Thank you again for all your knowledge and insight. It is greatly appreciated. _________________ Baja Dune 150
9 gram rollers, Yellow main spring, Uni Filter w/pre charger, HP CDI, HP Coil and Plug wire, Gutted exhaust, 130 main jet, all new balljoints and rod ends.
Articles
