My son's SLGK-150B 150CC cart has low hours and now will not start. Horn and signals work, so there is power. when i turn the key there is a faint whirring noise coming from the black 'fuse box' on the rear. The fuse is good. I'm not very 'mechanical' and am at a loss. Any ideas would be greatly appreciated.
thanks
JB i have the same buggy maybe i can help some not the best on electrical but i have had a few problems to,just might be a loose wire.
in the electrical box track down the 2 small wires coming from the starter solenoid.i marked it in yellow make sure these connectors are good and tight.the one marked red the starter solenoid make sure the 2 big wires are tight to.be careful don't over tighten and brake lug loose from solenoid, also watch when checking these wire to see if they are tight with a wrench or socket not to ground them to metal.the one closest to the buggy is hot all the time.
then go to battery track black ground wire to cvt cover and make sure they are tight to, also it wouldn't be a bad idea to take them off and see if there is still paint on the cvt cover.if there is paint there scrape it off put all the wires back on and tighten down.
the turn signal, horn and brake light works off the battery, they will work all the time if battery is charge up.
sorry for being so windy but check these things out first.
hope this helps
pud
ill second pud on that cvt paint where the ground wire goes. my buggy did the same thing after i painted my cvt cover but like a dumby i didnt cover that part of the cover where the ground goes. i think he pretty much covered it all except what could be wrong if its not any of the things he mentioned......the solinoid does make a noise when it goes bad. ive replaced 2 of them in 8 months.....i dont know how or why but they did go bad and make funny whinney clicking noise while i was cranking the motor. good luck _________________ Blade 150DX
2K RPM clutch springs 2K lb. torque spring
prodigy variator 10G sliders, prodigy pro clutch and Bell
37T sprocket
kevlar belt
Racing CDI, high out put coil, iridium spark plug
rejet carb 115
snorkle extension for intake and CVT breather
have a drink for me to, i have been messing with lights on my buggy all afternoon,checked all the wiring and rectifier and all it was was blowed bulbs
have you tried adjusting the cable back at the reverse box.
and loosen the cable up some to see if it will go into forward.
pud _________________ 2006 sunl 150b
Dr. pulley 10 gram sliders, 1500 torque spring,39 tooth sprocket,2000lb winch, red neck uni filter, 125 main jet at 1,450 elevation, drilled out exhaust,ngk iridium plug,performance intake
Check with BIGE he can probably get you the part you need _________________ 150cc Rocketa
'84 Honda Big Red 200
'96 Suzuki King Quad 300
'54 NAA Tractor
Always looking to add to the collection
If you are going through them so quick you might want to consider getting a solenoid for an older Ford and use it. It is designed to handle a lot of amps through the contacts and that is what usually goes wrong is the internal contact burn up. You can purchase one for around $12-$15. The last time I had to buy one. _________________ 150cc Rocketa
'84 Honda Big Red 200
'96 Suzuki King Quad 300
'54 NAA Tractor
Always looking to add to the collection
jredd29, what color are the wires coming out of it? I have several and all have different colors. _________________ Blade buggies,Carter buggy's Atv's, parts and repairs. accessories for all makes.
Romaha products dealer
MRP dealer
Tucker Rocky Dealer
Vega Helmet dealer
I.T.P. tire and wheel dealer
www.mcdonoughpowersports.com
Articles
