Hey guys, I was wondering if anyone can help me out here. I seem to be having problems with the shifting on my Talon. At first I couldn't get it to go into reverse. When you would put the shifter in the reverse position you would just hear the clutch slipping. So I tried to make some adustments to the cable. Then I couldn't get it to go forwards OR in reverse. Then after a few more adjustments it would ONLY go in reverse - even when the shifter was in the forward position. Now I'm back were I started, with it only wanting to go forwards.
Can you guys help point me in the right direction here? Do I maybe need a new cable? Am I doing something wrong on the adjustments? _________________ 2007 Carter Talon GSR 150 2R
To adjust the reverse cable, start with the lever in reverse (cable tensioned) with the rear of the buggy on stands and tighten the cable until the planetaries are fully engaged into reverse (I did this with the engine off and spun the rear wheels until the gears mate up well and no longer make noise). Forward may have some slack in the cable, but this is fine. _________________ 07 Joyner SandSpider 650
06 Tank Touring 150SE
06 Weekend Warrior WideBody FB2200
05 Ford F-250 PowerStroke
04 Yerf-Dog Spiderbox 3206
04 Kawasaki Concours ZG1000-A19
03 VW Jetta Wagon TDI
81 Honda Passport C70
Someone told me to try taking the clutch apart to see if there is dirt or something in there. Does that sound like a possibility? _________________ 2007 Carter Talon GSR 150 2R
Check that you are not idling too high,this loads up the box. _________________ If its got boobs,wheels or propellers-its gunna give u trouble!!
Kinroad Racer 700 EFI Polaris Hybrid
1966 Oldsmobile 98 Convertible
I agree w/andymc ... set idle as low as possible !!
Quote:
Someone told me to try taking the clutch apart to see if there is dirt or something in there. Does that sound like a possibility?
I think you should try taking the Rev. G/box apart & inspect/repack full of good high temp grease. If your clutch works fine in Forw; will be fine in Rev as well. On cable adjustment Pghruby described the easiest way to get this set, then for me small adj (1/4 to 1/2 turn) often fine tuned this problem away; if not, u in same boat as me... GSR--needs new cable. _________________ Team Farm...
07Joyner 650 SandSpider-Weber carb;Custom headers;ign mod;
07Carter GTR250-uni filter;irrid.plug;exh mod;tuff custom ch.guard;
06CarterGSR150R2-Dr.Pulley clutch,;uni filter;140 main;irrid.pl,ug;Teflon variator w/9gr;1500lb.spring;mod exh;
if not, u in same boat as me... GSR--needs new cable.
Well, turns out that's what it was all along. I found a spot on the cable were it was tied under the frame that was chaffed and had rusted. I guess I must have hit it in a rock or something. Anyways, I tied it back up on top of the frame to keep that from happening again. _________________ 2007 Carter Talon GSR 150 2R
Yea; Glad to hear it Sometimes; for me, just the imput from everyones comments encourages me to keep trying... Now Go Ride !!! A good ride always seems to make my day (anyday) Better. _________________ Team Farm...
07Joyner 650 SandSpider-Weber carb;Custom headers;ign mod;
07Carter GTR250-uni filter;irrid.plug;exh mod;tuff custom ch.guard;
06CarterGSR150R2-Dr.Pulley clutch,;uni filter;140 main;irrid.pl,ug;Teflon variator w/9gr;1500lb.spring;mod exh;
Articles
Sometimes; for me, just the imput from everyones comments encourages me to keep trying... Now Go Ride !!! A good ride always seems to make my day (anyday) Better.
