| Author |
Message |
| < Off Road Go Kart & Mini Buggy Discussion ~ Booger'd up my threads! What size where they?? |
|
|
|
|
As one thing leads to another, I booger'd up my threads on my drive pully shaft (the one the rollers are on). Any one know what size they are? I'm going to run a die on to see if I can clean up the outter threads (inner still look good). To me, it seems like they'd be M12x1.25??
|
|
|
|
 |
Sponsor
|
|
|
|
|
|
|
I ran into that problem once myself I went looking for a die to run over it and it was hard to find had to order one from napa, 2 days later and only 3 bucks I got my die. Your right on the size it's a 12x1.25
_________________
2006 Blade 150DX
10 gram rollers,
1500 clutch spring,
high rpm cam.
uni filter, performance pipe, 132 jet
Prodigy Variater
High Output Coil
NGK Iridium plug
|
|
|
|
|
|
|
|
|
Good thing is my brother owns a mechanic shop!!!  Just hope he can dig that one out for me!
Thanks again!!
Shaun
|
|
|
|
|
Sponsor
|
|
|
|
|
|
|
I did the same thing. Bought a thread chaser off the snap-on truck. I don't remember the price, but it was less than 15 bucks.
_________________
05 Jehm Adventure Buggy 250cc, Torque Spring, 22.5gr Rollers, Modified Roll Cage, K&N, 21x7x10 & 22x11x10 Trac Star Radials, Vapor, Body Panels, 40T Spkt
&
2003 Jehm Blazer 125cc, Vapor
10 gram rollers, 20x10x8 Razr's,
34 tooth sprocket, 9pk cooler
|
|
|
|
|
|
|
|
|
i almost done the same thing, i let the air gun get a little wild with me.my tap and die set only goes to 10mm
i will put this in my little book
also is thread size the same on the shaft that holds the clutch assembly on.i know the nut is a little bigger than the 17mm
nut on variator.
pud
_________________
2006 sunl 150b
Dr. pulley 10 gram sliders, 1500 torque spring,39 tooth sprocket,2000lb winch, red neck uni filter, 125 main jet at 1,450 elevation, drilled out exhaust,ngk iridium plug,performance intake
trying a set of 10gram rollers now
|
|
|
|
|
|
|
|
|
Be sure to write that down Pud. I may need to ask you what size that is one day 
_________________
DRIVE IT LIKE YOU STOLE IT!!!!!!!!!
DAZON 150 SINGLE SEAT
2.5inch rear wheel spacers
1.5inch front wheel spacers
UNI, 130jet, BIGE built intake tube, custom built exhaust, royal purple oil
|
|
|
|
|
Sponsor
|
|
|
|
|
|
|
got ya
_________________
2006 sunl 150b
Dr. pulley 10 gram sliders, 1500 torque spring,39 tooth sprocket,2000lb winch, red neck uni filter, 125 main jet at 1,450 elevation, drilled out exhaust,ngk iridium plug,performance intake
trying a set of 10gram rollers now
|
|
|
|
|
|
|
|
|
My brother only had the 1.5 and the 1.75  But not to worry, ordered the thing from Matco Tools (online). It was $5.30 and shipping was about 7 bucks. Here is the link if it will help anyone.....http://www.matcotools.com/Catalog/toolcatalog.jsp?cattype=T&cat=2166
|
|
|
|
|
|
Articles
